崗位職責:
- According to new project plan, implement activities of part development related with supplier, ensure part released in time;
- 根據項目計劃,實施供應商相關產品開發活動,確保按項目計劃完成產品放行;
- Based on part specification, handle supplier responsible complain, and feedback to related department;
- 基于零件規范,處理供應商零件相關投訴,并反饋給相關部門:
- Receive supplier complain information from related departments, based 8D method, take internal actions in plant to avoid further quality risk to production;
- 從相關部門獲得供應商相關的質量投訴信息,根據8D方法,在內部采取措施,避免不良零件對生產產生進一步質量影響;
- Push supplier analysis root cause, define & implement corrective actions, then assessment report from supplier, to ensure root cause is defined correctly, corrective actions are implemented, avoid failure happen again;
- 推動供應商分析失效原因并定義實施改進措施,然后評估供應商的報告,確保失效根本原因清楚定義,以及改進措施的實施并起到預期效果,避免失效再次發生;
- Feedback status of complain internal, share lesson learn with different plants & suppliers if necessary;
- 在內部反饋投訴的狀況,并在必要時共享經驗教訓給不同的工廠及供應商;
- According to result of part release and related specification, define & maintain inspection plan in SAP in time;
- 根據零件放行結果和相關規范,及時在SAP中定義并維護進料檢驗計劃;
- Keep monitor supplier performance, take continue improvement actions, to achieved defined supplier quality target;
- 持續監控供應商質量表現,采取持續改進措施, 以達成約定的供應商質量目標;
- Support customer & third part visits/audits in SGCC for supplier topics.
- 支持客戶/第三方機構審核中關于供應商相關的事項。
任職要求:
- Bachelor degree in mechanical or electrical engineering;
- 統招本科學歷,機械或電機工程專業;
- More than 3 years working in automotive industry as supplier quality assurance;
- 至少3年汽車行業供應商質量管理工作經驗;
- Know well about IATF16949 system;
- 了解TS16949質量體系要求;
- Know well about quality tool, APQA, PPAP, MSA, FMEA, and SPC etc;
- 掌握相關質量工具,如APQP, PPAP, MSA, FMEA, SPC, 等;
- Experience of supplier audit & process release based on VDA6.3;
- 有基于VDA6.3的供應商評審以及過程放行經驗;
- Know well about 8D method and can use 8D method to solve quality issue;
- 了解8D方法,并能運用8D方法解決質量問題;
- Knowledge of measuring technology;
- 掌握測量技術及要求;
- Good communication skill;
- 良好的溝通技能;
- Good command of English in reading, writing, listening and speaking.
- 良好的英語聽、說、讀、寫能力。
- Accept frequent business trips
- 可接受頻繁出差